The learn button is sometimes located on the back of the unit, or with Excelerator openers, it is under the light lens near the hinge of the lens globe. With most Genie units, remove the light lens globe to expose the Learn Button on the motor head. Go to next machine and follow steps 8 to 13.Test by Opening Cover, Enter PIN1, Enter 1.Follow directions below to set each door.Press “SEND” once to test system and start your door moving.
CHANGE PIN GENIE INTELLICODE KEYPAD CODE
Press “SEND” 2 times for your system to grab your frequency and code it in.Enter your PIN number after pressing the Learn Code button described above, while the motor head indicator light is blinking.When pressed, a radio signal indicator will start blinking red for 30 seconds. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head. Gently press and release the Receiver Learn Code button on the Power Head Receiver of your Genie Garage Door Opener (Genie motor on the ceiling). To access, press inward, under the number pad lip while sliding downward to expose the battery. Check the 9 volt battery under the keypad numbers. Note: if red indicator light does not blink, it is not taking the programming steps. Enter your Personal Identification Number (PIN).Open cover fully by sliding keypad cover up until it latches.To Program the Intellicode Wireless Keypad Indicator light will blink once and go out. Press and hold “PROG” and “8” while fully opening cover.GWKIC, ACSDG, Two Part, Step-By-Step Programming Model 1: Intellicode Model GWKIC, ACSDG ( black with slide-up cover and the word “Intellicode” printed on the cover) Genie Wireless Intellicode Keyless Entry Pad Programming: 3 Models Test Keypad by sliding cover up until it latches.Enter Door Code, as determined from the chart above, and press the “star” key.Your PIN number can be created from any group of numbers up to 8 digits of your choice. Enter your PIN and press the # button.Press 3, 5, 7 and # buttons in said order.If the back lit keypad light goes out, close the cover pad and reopen it until it clicks. At this point, if the back lit keypad light stays on, proceed directly to step 2. While pressing the # and 8 buttons simultaneously, slide the Keypad Cover the rest of the way up until it latches. Reset Keypad–slide keypad cover half way up.You can then print out a legible copy of the chart and the programming instructions from your word software. To make a copy, highlight area and copy into your word program. You should have 3 or 4 Door Code numbers. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. Determine the settings of the first 3 switches and write down the corresponding number from the chart. The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. Keypad is black with a slide-up cover showing the Genie logo only) ( works with remotes having 9 or 12 internal code setting switches. If you cannot find your remote control, you will need to erase all of the remote control codes from the receiver's memory and reprogram them.Outside Keypad Programming Genie Garage Door Opener Keypads Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK If it does, you will need to replace the wall unit. Also see that the wall control does not have a shorted or sticking button. If your wire has been cut, you will need to replace it. If your garage door runs for no apparent reason, first check the staples on the wire from the power head to the wall control and make sure they are not cutting insulation and shorting wires. Once you are done, you will need to wait about 20 minutes for the protector to reset. Make sure the motor protector is not open. If the power source is not your problem, check all of the connections at the power head terminals. If you have no power, check for a tripped circuit breaker or a blown fuse. Ensure that there is power to the outlet by plugging another appliance into it. If your Genie Intellicode garage door opener does not run from the wall control, check to make sure the lock switch on the wall console is not turned on.
0 kommentar(er)
